Reference data
Bolt glossary
Plain-English definitions for the terms that turn up on fastener drawings and purchase orders.
Bolt glossary
- Across flats
- The distance between two opposite parallel faces of a hex or square head or nut. It sets the wrench size.
- Anchor bolt
- A bolt or rod embedded in concrete that connects a structure or equipment to its foundation.
- Bearing surface
- The face of a head or nut that contacts the part being clamped.
- Clevis
- A U-shaped fitting with a cross pin, used to give a rod a pivoting connection.
- Cut thread
- A thread machined from full-diameter stock, leaving the shank larger than the thread root.
- Galvanizing
- Coating steel with zinc, usually by hot dipping, to protect it from corrosion.
- Grade
- A designation for the mechanical properties of a fastener, set by standards such as ASTM or SAE.
- Grip
- The thickness of the material a bolt clamps, measured from under the head to the first full thread.
- Heavy hex
- A hex head or nut with larger across-flats than the regular pattern.
- Hot forging
- Heating bar stock until it is plastic, then upsetting it in a die to form a head.
- Jam nut
- A thin nut tightened against another to lock it in position.
- Pitch
- The distance between adjacent thread crests; for inch threads, 1 divided by threads per inch.
- Pitch diameter
- The diameter of the imaginary cylinder where the thread width equals the space between threads.
- Proof load
- The load a bolt must carry without permanent deformation during testing.
- Rolled thread
- A thread formed by displacing material with hardened dies rather than cutting it away.
- Swage
- To reduce the diameter of a rod end by forging so a thread can be cut without losing strength.
- Tensile strength
- The maximum stress a material withstands before it fractures.
- Turnbuckle
- A threaded fitting with opposite-hand threads that adjusts the tension in a rod when rotated.
- Hydrogen embrittlement
- Loss of ductility in very high-strength steel caused by absorbed hydrogen, which can lead to sudden fracture. It is why A490 bolts are not hot-dip galvanized.
- Mill test report
- A certificate from the steel mill giving the chemistry and mechanical test results for the heat of steel a fastener was made from.
- Nut factor (K)
- The empirical coefficient in T = K·D·P that links installation torque to bolt tension. It depends on lubrication, coating and thread condition.
- Overtapped nut
- A nut tapped slightly oversize before galvanizing so it will run onto a coated bolt thread.
- Plate washer
- A thick plate with a hole, used under the nut of an anchor rod to spread the load into the base plate.
- Pretension
- The tension deliberately installed in a bolt when it is tightened. A pretensioned joint clamps the plies together so load passes by friction.
- Property class
- The ISO 898-1 strength designation for a metric bolt, such as 8.8 or 10.9. The first number times 100 is the tensile strength in MPa; the second times 10 is the yield percentage.
- Slip-critical
- A joint designed so the bolts never slip into bearing under service load. It relies on pretension and faying-surface condition.
- Snug-tight
- The condition reached when the plies are in firm contact: the full effort of a person with a spud wrench, or a few impacts of an impact wrench.
- Stress area
- The effective cross-section of a threaded bolt, used to calculate its tensile load. It lies between the pitch-diameter and minor-diameter areas.
- Thread class
- The tolerance class of a thread. For inch threads 1A / 2A / 3A are external and 1B / 2B / 3B internal; 2A / 2B is the general fit.
- Type 3
- The weathering-steel variant of a structural bolt, nut or washer, so the fastener weathers like the steel it joins.
- UNC / UNF / 8-UN
- Unified inch thread series: coarse, fine, and the constant-pitch series with 8 threads per inch.
- Yield strength
- The stress at which a material begins to deform permanently.
Prepared from the published tables of the standards named and cross-checked against secondary references. It is a working reference, not a substitute for the standard: confirm against the current edition before using it in design, specification or procurement.
Ready to get a quotation?
Build a list of products and quantities, or send a sketch or a drawing. Our sales team replies with a quotation.