Imperial / ASTM specifications
The imperial path: ASTM, ASME, SAE and AASHTO standards, grades, UNC / UNF / 8-UN threads and the calculators set to inches, ksi and kips.
21 ASTM, ASME, SAE and AASHTO standards
Dimensions in inches, strength in ksi, force in kips, torque in ft·lb.
Bolts & rods
- ASTM F1554 Anchor Bolts, Steel, 36, 55 and 105 ksi Yield Strength
- ASTM A307 Carbon Steel Bolts, Studs and Threaded Rod, 60,000 psi Tensile Strength
- ASTM F3125 High Strength Structural Bolts, Steel and Alloy Steel, 120 ksi and 150 ksi Minimum Tensile Strength
- ASTM A449 Hex Cap Screws, Bolts and Studs, Steel, Heat Treated, 120/105/90 ksi Minimum Tensile Strength
- ASTM A354 Quenched and Tempered Alloy Steel Bolts, Studs and Other Externally Threaded Fasteners
- ASTM A193 / A193M Alloy-Steel and Stainless Steel Bolting for High Temperature or High Pressure Service
- ASTM A320 / A320M Alloy-Steel and Stainless Steel Bolting for Low-Temperature Service
- SAE J429 / J995 Mechanical and Material Requirements for Externally Threaded Fasteners (J429) and Nuts (J995)
Nuts
- ASTM A563 / A563M Carbon and Alloy Steel Nuts
- ASTM A194 / A194M Carbon, Alloy and Martensitic Stainless Steel Nuts for High-Pressure or High-Temperature Service
Washers
- ASTM F436 / F436M Hardened Steel Washers
- ASTM F844 Washers, Steel, Plain (Flat), Unhardened for General Use
- ASTM F959 / F959M Compressible-Washer-Type Direct Tension Indicators for Use with Structural Fasteners
- ASME B18.22.1 Plain Washers
Coatings
- ASTM A153 / F2329 Zinc Coating (Hot-Dip) on Iron and Steel Hardware, and on Threaded Fasteners
Steel & bar
- ASTM A36 / A36M Carbon Structural Steel
- ASTM A615 / A615M Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement
Dimensions & threads
- ASME B18.2.1 / B18.2.6 Square, Hex, Heavy Hex and Askew Head Bolts (B18.2.1) and Fasteners for Use in Structural Applications (B18.2.6)
- ASME B18.2.2 Nuts for General Applications: Machine Screw Nuts, Hex, Square, Hex Flange and Coupling Nuts
- ASME B1.1 Unified Inch Screw Threads (UN and UNR Thread Form)
Cross-reference
- AASHTO M-series AASHTO Material Specifications for Highway Bolting and Hardware
Set to this path's units
All calculators work in both systems. Typed values carry across when you switch.
Bolt weight calculator
Weights of bolts, nuts and washers with a running order tally. Inch or metric.
OpenCalculatorsPlate weight calculator
Square or round plate with an optional hole.
OpenCalculatorsTie rod calculator
Rod length to order from a pin-to-pin dimension, with clevis and turnbuckle allowances.
OpenCalculatorsUnit converter
Length (with fractions), force, stress, torque, mass and area between inch-pound and SI.
OpenCalculatorsBolt strength calculator (AISC 360 / Eurocode 3)
Tension and shear resistance per bolt, LRFD or ASD, with the tension-shear interaction check; or EN 1993-1-8 for metric bolts.
OpenCalculatorsAnchor rod steel strength (ACI 318)
Steel tension and shear strength of cast-in anchors by grade, with the ductility check. Concrete failure modes are not covered.
OpenCalculatorsTorque and preload calculator
Target preload and installation torque from T = K·D·P for any bolt grade and nut factor.
OpenCalculatorsBolt length (grip) calculator
Length to order from the grip, washers, nut and thread projection, rounded up to stock.
OpenCalculatorsSpecification selector
Choose the bolt, nut, washer and coating specification for an application, with example specification wording.
OpenTables and charts
Need a specification checked?
Send the clause, the drawing note or the datasheet. We will tell you what it asks for and what it would cost to supply.