Technical resources
Specifications, material data, design calculators and reference tables for anchor bolts and construction fasteners. Choose a specification path below, or search everything.
- 26 standards
- 7 materials
- 9 calculators
- 13 reference tables
- 3 guides
Metric specifications
ISO and EN standards, property classes, ISO metric threads and metric reference data. 5 standards plus the ISO metric thread tables.
Open the metric pathInches, ksi, kipsImperial / ASTM specifications
ASTM, ASME, SAE and AASHTO standards, grades, UNC / UNF / 8-UN threads and inch-series reference data. 21 standards.
Open the imperial pathDesign aids and take-off tools
Every calculator works in metric and imperial. Switch with the unit toggle in the header; typed values carry across.
Bolt weight calculator
Weights of bolts, nuts and washers with a running order tally. Inch or metric.
OpenCalculatorsPlate weight calculator
Square or round plate with an optional hole.
OpenCalculatorsTie rod calculator
Rod length to order from a pin-to-pin dimension, with clevis and turnbuckle allowances.
OpenCalculatorsUnit converter
Length (with fractions), force, stress, torque, mass and area between inch-pound and SI.
OpenCalculatorsBolt strength calculator (AISC 360 / Eurocode 3)
Tension and shear resistance per bolt, LRFD or ASD, with the tension-shear interaction check; or EN 1993-1-8 for metric bolts.
OpenCalculatorsAnchor rod steel strength (ACI 318)
Steel tension and shear strength of cast-in anchors by grade, with the ductility check. Concrete failure modes are not covered.
OpenCalculatorsTorque and preload calculator
Target preload and installation torque from T = K·D·P for any bolt grade and nut factor.
OpenCalculatorsBolt length (grip) calculator
Length to order from the grip, washers, nut and thread projection, rounded up to stock.
OpenCalculatorsSpecification selector
Choose the bolt, nut, washer and coating specification for an application, with example specification wording.
Open26 standards, one template
Each page gives the grades and their properties, the matching nut and washer, coating notes, what to write in a specification, and the cross-references.
Bolts & rods
Coatings
Steel & bar
Dimensions & threads
Cross-reference
What the fasteners are made from
A36 carbon structural steel
The default plate and bar steel for base plates, plate washers and fabricated brackets. Mild, weldable and inexpensive.
OpenMaterialsA572 Grade 50 high-strength low-alloy steel
A higher-yield structural plate, used where a thinner base plate or higher bearing capacity is wanted.
OpenMaterialsWeathering steel (A588 / A709 Grade 50W)
Steel that forms a stable rust patina in alternating wet and dry conditions, used for bridges and exposed architectural steel without paint.
OpenMaterialsChromium-molybdenum alloy steel (AISI 4140 / 4142)
The quenched-and-tempered steel behind A193 B7 and most high-strength anchor rods and studs.
OpenMaterialsType 304 austenitic stainless steel
The general-purpose stainless: good in clean atmospheres, poor in chlorides. Fasteners are A193 B8 or ISO A2.
OpenMaterialsType 316 austenitic stainless steel
304 with molybdenum added for chloride resistance. The usual stainless choice for marine and coastal fastening.
OpenMaterials2205 duplex stainless steel
Roughly twice the yield strength of 316 with better chloride and stress-corrosion resistance. For severe marine and chemical exposure.
OpenTables and charts
Practice notes
Specifying anchor rods: what the drawing needs to say
A checklist for the anchor bolt plan, and the mistakes that cost a week on site.
OpenGuidesGalvanizing fasteners: what designers need to know
Which standards apply, why nuts are overtapped, and which high-strength steels should not be hot-dip galvanized.
OpenGuidesWorking across inch and metric bolting
Why a 1/2 in. bolt is not an M12, how the strength classes compare, and what to put on an international enquiry.
OpenThis is a working reference prepared from published standards and cross-checked against secondary sources. Confirm against the current edition of the governing standard before relying on it in design or procurement. Calculators are design aids, not a substitute for the engineer of record.
Need a specification checked?
Send the clause, the drawing note or the datasheet. We will tell you what it asks for and what it would cost to supply.